GPS16X-HVS GPS Receiver with Integrated Antenna

Precision time synchronization

The GPS16X-HVS is a global positioning system (GPS) receiver that provides position, velocity, and timing information. Campbell Scientific configures the GPS16X-HVS and modifies its cable so that the receiver can more easily interface with our data loggers. 

Category:

The GPS16X-HVS, manufactured by Garmin International, consists of a receiver and an integrated antenna. It receives signals from orbiting Global Positioning System (GPS) satellites and then uses the signals to calculate position and velocity. The GPS16X-HVS also provides a highly accurate one-pulse-per-second (PPS) output for precise timing measurements. 

Default settings are typically used. The default settings and options are changed using GPS16 software, which is available, at no charge, from the Garmin website (www.garmin.com). Additional hardware is required to connect the GPS16X-HVS to the computer running the GPS16 software (see Ordering Information for more  information). 

By default, the instruction expects the GPS unit to be set up at 38400 baud, outputting the GPRMC and GPGGA sentences once per second. The data logger expects the start of the second to coincide with the rising edge of the PPS signal. If there is no PPS signal or if the required sentences come out at less than once per second, the data logger will not update its clock. 

GPS units with lower baud rates can be used with the GPS instruction, but the baud rate has to be set for the relevant Com port it is to be connected to either in the data logger settings or by including a SetStatus command after the BeginProg instruction in the program (for example, SetStatus(“BaudrateCOM4”,19200)). Baud rates below 2400 bps will not work, as the GPS unit will not be able to transmit the two GPS sentences once per second reliably. Similar problems can be encountered even at higher baud rates if too many optional GPS strings are selected to be output. 

Benefits and Features 

    • Supports real-time WAAS or RTCM corrections for accuracy of 3 to 5 m 
    • Attaches directly to a CR300-series, CR6, or CR1000X, regardless of functionality 
    • Connects directly to a CR800, CR850, CR1000, or CR3000 datalogger when PPS time-synchronizing functionality is not used. 
    • Processes data from up to 12 satellites depending on the number of satellites viewable above the horizon 
    • Allows the data logger clock to be set to the highly accurate GPS time 
    • Configured by Campbell Scientific to output RMC and GGA data strings at 38400 bps 
    • Extremely accurate timing pulse (PPS) can be used to synchronize time between the data logger and other instruments 
Receiver WAAS enabled. 12 parallel channel GPS receiver continuously tracks and uses up to 12 satellites (up to 11 with PPS active) to compute and update the position.
Update Rate Factory set to 1 s between updates. (Programmable from 1 to 900 s.)
PPS Output 1 Hz pulse; 1 µs accuracy (Width factory set to 100 ms.)
Baud Rate Factory set to 38400 bps.
Operating Temperature Range -30° to +80°C
Storage Temperature Range -40° to +80°C
Operating Voltage Range 8 to 40 Vdc
Current Drain 65 mA active (@ 12 Vdc)
Velocity Accuracy 0.1 knot RMS steady state
Cable Length 4.57 m (15 ft)
Diameter 9.1 cm (3.58 in.)
Height 4.2 cm (1.65 in.)
Weight 332 g (12 oz)
Position Accuracy (95% typical)
GPS Standard Positioning Service (SPS) < 15 m
DGPS (USCG/RTCM) Correction 3 to 5 m
DGPS (WAAS) Correction < 3 m
Acquisition Times
Reacquisition < 2 s
Hot ~1 s (all data known)
Warm ~38 s (initial position, time and almanac known, ephemeris unknown)
Cold ~45 s

 

Brochures: GPS16X-HVS Geographic Position Receiver

Download

Manuals: GPS16X-HVS GPS Receiver

Download

Product reviews

Review GPS16X-HVS GPS Receiver with Integrated Antenna

5 0% | 0 review
4 0% | 0 review
3 0% | 0 review
2 0% | 0 review
1 0% | 0 review
Review GPS16X-HVS GPS Receiver with Integrated Antenna
Choose a image
0 character ( Minimum of 10)
    +

    There are no reviews yet.

    No comments yet

    Related products

    Bộ thu thập và xử lý dữ liệu Granite 10

    Granite 10 Measurement and Control Data-Acquisition System

    Ideal for automotive testing applications, featuring CAN bus and CAN FD output
    Find out more
    Mô-đun Đầu vào Cổng Dòng điện 100 Ohm CURS100

    CURS100 100-Ohm Current Terminal Input Module

    Expands capabilities, allows data logger to measure additional types of sensors
    Find out more
    Datalogger ba kênh cho cảm biến dây rung CRVW3-NE

    CRVW3-NE Three-Channel Vibrating Wire Datalogger without Enclosure

    Vibrating Wire Data Logger Using patented VSPECT™ technology
    Find out more
    Bộ Ghi Dữ Liệu Dây Rung Ba Kênh CRVW3

    CRVW3 Three-Channel Vibrating Wire Datalogger

    Self-Contained Vibrating Wire Data Logger Using patented VSPECT® technology
    Find out more
    Bộ ghi đo tự động Datalogger CR6

    CR6 Automated Monitoring Platform

    Rugged, wireless edge device and gateway with built-in connectivity, designed for geotechnical, structural, and environmental projects
    Find out more
    Bộ ghi dữ liệu đo lường và điều khiển CR350

    CR350 Measurement and Control Datalogger

    Compact data logger with RS-485, ideal for small applications
    Find out more
    Bộ ghi dữ liệu đo lường và điều khiển CR310

    CR310 Measurement and Control Datalogger

    Compact data logger with ethernet, ideal for small applications
    Find out more
    Bộ ghi dữ liệu đo lường và điều khiển CR300

    CR300 Measurement and Control Datalogger

    Compact data logger, ideal for small applications
    Find out more

    Subscribe to Content

    If you need to copy the content, please leave your information, and we will respond as soon as possible. Sincerely, thank you!